Izdelki za jeklena jekla (236)

High Accuracy Taper and External Diameter Wide range of Sizes Available These reduction bushes allow for the fitting of boring bars and drills with a tapered shaft. All sizes are manufactured in a range of capacities. The sleeves are hardened and ground for a good fit for both the holder and the shaft. Estimated delivery:3-5 Working Days (subject to availability)

Clamps and Pulls Down Component Available Ground or Serrated Low Profile Jaw for Thinner Components Vise mounted directly to the machine bed. Low profile jaw allows for more tool clearance. The actuation not only clamps the components but also pulls it down. The jaws are available in smooth or serrated. Parts CP15 and CP16 work as stop for this vise. Estimated delivery:5-7 Working Days (subject to availability)

Reduce setup and changeover times by up to 80% Eliminate out of round conditions and concentricity problems Effectively double the holding capacity of any chuck without eliminating the ability to hold small parts Light-weight 6061 T-6 or 319 for weight saving DESCRIPTION Abbott‘s master plate and segment system is a great choice for turning larger diameter work pieces. The system consists of an aluminum master plate, similar to a thin Pie Jaw®, which is pre-drilled and keyed to accommodate Abbott’s standard, off-the-shelf segment rings. Plates are available in various diameters from 15 to 60 inches and can be mounted on 8-60 inch diameter chucks, effectively increasing the holding capability of smaller chucks. The master plate can be custom machined to fit any model chuck, making it a permanent universal fixture on any machine.When using this system, the transition from one job to the next simply requires bolting on a new size or configuration of segments before continuing Estimated delivery:5-7 Working Days (subject to availability)

Hardened and Ground Supplied in sets of 3 Ground Serrations for Accurate Positioning of top Jaws Set of three replacement base jaws. Base jaws are normally replaced in the event of a crash. Please check the condition of slide ways in the chuck before replacing. Replacement of base jaws will not necessarily increase accuracy. Any damage or wear to the chuck body itself cannot be rectified. Estimated delivery:2-3 Weeks (subject to availability)

Buy Pure Copper Wire Scrap with a 99.8% copper content. We offer high-quality copper wire scrap for purchase. Our scrap is of the highest purity and is perfect for a variety of applications. Contact us today to get the best deals and prices. Overview Essential details Place of Origin: Germany / Netherlands Brand Name: CRX Model Number: Copper Wire Type: Copper Wire Copper Content: 99.99% Product Name: Pure Copper Wire Scrap 99.8% Copper Keyword: Copper Scrap / Copper Wire For Sale MOQ: 1 Ton Material: 99.995% Pure Copper Shape: Bare Wire Package: Customers' Request Delivery Time: 7-14 Days Wire Diameter: 0.2~3MM Length: Customized Length Supply Ability Supply Ability: 500 Ton/Tons per Week Packaging & delivery Packaging Details: AS BUYER REQUEST Port: USA Lead time 1 - 100 metric tons : 5 days Above 100 metric tons : To be negotiated

1/8" Range per Collets Sizes Up To 50.8mm Across Flats Smooth Bore as Standard, Other Finishes Available Special Profiles Available DESCRIPTION D120 Varibore hex collets are to suit 54mm capacity collet chucks. Also known as V120, these collets have a 3.175mm range. Supplied smooth as standard we can supply with alternate finishes and in special profiles. D120 suit the following collet chucks: Klamp CRL54 Klamp CRS54 Klamp QCRL54 Crawford CDC54 Crawford CDC-54-S Crawford QC-54 Estimated delivery:2-3 Weeks (subject to availability)

Hot rolled steel hexagon GOST 2879 and cold rolled (calibrated) GOST 8560 are produced from carbon, alloy, nickel containing, tool, spring spring, automatic, bearing and heat resistant steels. The main purpose of the metal hexagon is the further production of hardware products for wrenches and tools. Steel workpieces are machined mechanically on lathe, turret lathe and CNC machines. Also, the product can be found in parts and assemblies of cars, agricultural machinery and other machines, car building, construction. Overall dimensions of the produced metallurgical rolled products 8 100 mm, length from 2 to six meters. Measurement of hot rolled and cold rolled hexagon is made on the flat part (d). You can buy (order) a steel hexagon by calling us by phone and writing to the website widget. All of its assortment presented is available in the covered hangar. Hexagon price = factory price, its adjustment is possible upon agreement of the delivery schedule HEXAGON STEEL HOT-ROLLED (GOST 2879-88) st. 3; twenty; 35; 45; 20X; 40X:8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 20,8, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 32 HEXAGON STEEL HOT-ROLLED (GOST 2879-88) st. 3; twenty; 35; 45; 20X; 40X:34, 36, 38, 40, 41, 42, 43, 47, 48, 50, 52, 53, 55, 56, 57, 60, 63, 65, 70, 75, 80, 85, 90, 95, 100 Rolled calibrated hexagonal GOST 8560-78 Art. twenty; 35; 45 20X; 40X:8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 20,8, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 32 Rolled calibrated hexagonal GOST 8560-78 Art. twenty; 35; 45 20X; 40X:34, 36, 38, 40, 41, 42, 43, 47, 48, 50, 52, 53, 55, 56, 57, 60, 63, 65, 70, 75, 80, 85, 90, 95, 100

Hardened and Ground Supplied in sets of 3 Ground Serrations for Accurate Positioning of top Jaws Set of three replacement base jaws. Base jaws are normally replaced in the event of a crash. Please check the condition of slide ways in the chuck before replacing. Replacement of base jaws will not necessarily increase accuracy. Any damage or wear to the chuck body itself cannot be rectified. Estimated delivery:2-3 Weeks (subject to availability)

Product Features: • Spot welded steel - heavy duty construction chassis. • Finished in ASA 61 smooth grey or satin black powder paint. • Optional bottom plates are punched with 4 holes - 316" diameter (Chassis now includes 1/8" holes to allow installation of optional bottom plates). • Rubber feet sold separately. • Some models accept chassis covers (1451 Series). • Upgrade to the Satin Black Chassis with Walnut Sides (available for some sizes).

For more information on this product range please click the link above or simply visit https://kgaenclosures.com to view the complete range of enclosures, transformers and components we stock, all at great competitive prices.

Flanged PN16 (8” Available Flanged PN10), Cast Iron Body, Cast Brass Seat, Stainless Steel Stem, Inside Screw, Non-rising Stem, Conforms to DIN 3202 F4, Rated PN16, Temperature -10°C to 120°C.

Compatible with large, readily available, range of jaws Two stage gripping gives clamping and seating of part Base jaws do not protrude on z axis Sealed body designKitagawa chucks are manufactured from high grade alloy steel. The Kitagawa DL Series are the 1st chuck with two stage gipping action, firstly parallel clamping then pull back action for work seating. Estimated delivery:On Request

Allignment Busing and Thread Hole for Quick Accurate Set-ups Ground Flat and Parallel Locating Holes for easy Location Cast iron fixture plate with mounting holes. Grid pattern with allignment bushes and threaded inserts for ease of set-up. Ground flat parallel and perpendicular for accuracy. Two dowel holes allow for precise loading and setting up of the fixture plate. Estimated delivery:7-10 Working Days (subject to availability)

Reduce setup and changeover times by up to 80% Eliminate out of round conditions and concentricity problems Effectively double the holding capacity of any chuck without eliminating the ability to hold small parts Light-weight 713 Tenzaloy for weight saving DESCRIPTION Abbott‘s master plate and segment system is a great choice for turning larger diameter work pieces. The system consists of an aluminum master plate, similar to a thin Pie Jaw®, which is pre-drilled and keyed to accommodate Abbott’s standard, off-the-shelf segment rings. Plates are available in various diameters from 15 to 60 inches and can be mounted on 8-60 inch diameter chucks, effectively increasing the holding capability of smaller chucks. The master plate can be custom machined to fit any model chuck, making it a permanent universal fixture on any machine.When using this system, the transition from one job to the next simply requires bolting on a new size or configuration of segments Estimated delivery:2-3 Weeks (subject to availability)

Allignment Busing and Thread Hole for Quick Accurate Set-ups Ground Flat and Parallel Cast iron gridded angle plate .Grid pattern with allignment bushes and threaded inserts for ease of set-up. Ground flat parallel and perpendicular for accuracy. To suit verticle or horizontal machining centre applications. Estimated delivery:7-10 Working Days (subject to availability)

Screwed BSPP, Reduced Bore, 3 Way, Stainless Steel Body & Ball, RPTFE Seats, Rated PN63, Fitted with Pneumatic Actuator, Size for 5.5 Bar (80psi) Air Supply. Fully Assembled and Tested.

Switch between jaws and faceplates in seconds Clamp more complex workpieces Clamp more components at a time Load faceplates outside the machine for better efficiency Faceplates form the base for a fixture to mount directly to the QwikLOK. They are ideal for complex workpieces that cannot be mounted in soft jaws and also allow smaller workpieces to be clamped in larger quantities. Combine a faceplate with simple workstops and clamps to buld a multi component fixture that can be loaded outside the machine. Add another identical faceplate and you have a manual pallet changing system to virtuallly eliminate loading time. Estimated delivery:Next Day (subject to availability)

ASMS659 is a corrosion resistant steel. We hold this grade in round bar form in both the solution treated condition (Condition A) and in the H1025 precipitation treated (aged) condition. The material is typically used for part s requiring corrosion resistance and high strength up to 300oC. The material exhibits good ductility and strength in the transverse direction in large section sizes SIZES STOCKED: Condition A – 9.5 mm dia – 152.4 mm dia H1025 condition – 12.7 mm dia – 152.4 mm dia

Aggressive machining operations while clamping on as little as 1.5mm Ideal for difficult applications or proto-type work Jaws to suit round or complex profiles as well as regular shapes Available for 6" and 8" vices Increase the functionality of your standard 150mm and 200mm vices. This combo kit is a simple bolt on system that will allow you to perform aggressive machining operations on Square, round or complex parts while clamping on as little as 1.5mm. This set includes a set of TalonGrip jaws (Sets includes 4 TalonGrips, 1 stop and M5 screws) and a set of VersaGrip jaws (Set includes 4 VersaGrip with M5 Screws). Estimated delivery:3-5 Working Days (subject to availability)

Easy machining of round workpieces High precision and high clamping force Wide range of accessories for flexibility Maximise your machining envelope Fixed v-jaws for the SVF range of flexible vices. There are bolt-on hard v-jaws to fit all types of fixed jaw in the SVF range including wedge type and non-wedge type. These v-jaws have a centre key for accurate positioning. Estimated delivery:On Request

High Accuracy Taper and External Diameter Wide range of Sizes Available These reduction bushes allow for the fitting of boring bars and drills with a tapered shaft. All sizes are manufactured in a range of capacities. The sleeves are hardened and ground for a good fit for both the holder and the shaft. Estimated delivery:3-5 Working Days (subject to availability)

Universal quick change system for any chuck Repeatability < 0.001" TIR Reduce setup and changeover times by up to 80% Eliminate out of round conditions and concentricity problems DESCRIPTION When it comes to turning/holding smaller diameter parts Abbott’s precision master plate and segment system is an ideal choice for high changeover and short running jobs. Due to the system’s high repeatability, it is an excellent alternative to more expensive quick change chucks. The system consists of an aluminum master plate, similar to a thin Pie Jaw®, which is bored and bushed to accommodate Abbott’s standard, off-the-shelf pinned segments. Plates are available in 8, 10 and 12 inch diameters and can be mounted on 4-12 inch diameter chucks. The master plate can be custom machined to fit any model chuck, making it a permanent universal fixture on any machine.When using this system, the transition from one job to the next simply requires bolting on a new size Estimated delivery:2-3 Weeks (subject to availability)

Allignment Busing and Thread Hole for Quick Accurate Set-ups Ground Flat Five High Accuracy Location Holes Cast Iron Sub Plate to suit rotary table or indexer. Grid pattern with allignment bushes and threaded inserts for ease of set-up. Ground flat with Locating Holes for precise loading and quick location. Estimated delivery:7-10 Working Days (subject to availability)

Switch between jaws and faceplates in seconds Clamp more complex workpieces Clamp more components at a time Load faceplates outside the machine for better efficiency Faceplates form the base for a fixture to mount directly to the QwikLOK. They are ideal for complex workpieces that cannot be mounted in soft jaws and also allow smaller workpieces to be clamped in larger quantities. Combine a faceplate with simple workstops and clamps to buld a multi component fixture that can be loaded outside the machine. Add another identical faceplate and you have a manual pallet changing system to virtuallly eliminate loading time. Estimated delivery:Next Day (subject to availability)

Quick Change Mechanism Hardened for Longevity Clamping Surface is Grooved to Avoid Marking Component Custom Sizes Available For clamping workpieces that must not be damaged. The clamping surface is grooved and not ribbed. This results in reducing the potential for marking components. The stepped jaw is hardened approx. 0.2 mm deep. The accuracy of the surface with respect to the serration is +/- 0.02 mm. For greater accuracy, the jaws must be ground in tension on the vice. Estimated delivery:3-5 Working Days (subject to availability)

Maximise your machining envelope High precision and high clamping force Wide range of accessories for flexibility Clamp single large or multiple small workpieces Clamps to suit OK-Vise Multi-Rail. Multi-Rail can accommodate OK-Vise clamps, stops, parallels and other accessories to clamp multiple components and maximise your milling work area. All the clamping and location elements on the rail can be positioned according to the size and shape of the workpieces to swiftly adapt from clamping multiple small workpieces to clamping single large workpieces. These clamps are available in a range of styles and applications. Estimated delivery:7-10 Working Days (subject to availability)